Clinical Assessment Of Inlay Retained Bridge Designs (Tub Shaped And Inlay Shaped) In Missing Posterior Teeth Cases.
试验速览
- 阶段
- 不适用
- 入组人数
- 7
- 主要终点
- Fracture
研究概览
简要总结
The interest in partial coverage retainers such as inlays and onlays have increased drastically because these restorations are able to provide a more conservative option requiring minimal tissue removal thus preserving healthy tooth structure to a maximum extent.
If patient rejects an implant treatment and enough sound tooth structure is available it would be desirable to restore a missing tooth with Inlay-Retained Fixed Partial Denture instead of full coverage retained one .
The use of all-ceramic materials for inlays and onlays in restorative dentistry is becoming more popular , the proper selection of restorative materials, careful preparation design and adequate adhesion between tooth/restorative material interfaces considered important factor to prevent failures .
Zirconia was introduced into dentistry in the 1990s.The high initial strength and fracture toughness of zirconia results from a physical property of partially stabilized zirconia known as transformation toughening. On the other hand, its white color, similar to the color of natural teeth and its ability to transmit light makes it useful in aesthetically important areas .
Inlay Fixed Partial Denture restoration may have increased the risk of fracture due to the relative small size of restorations compared to the complete coverage restoration. An unfavorable distribution of stresses between the ceramic inlay and tooth structure may result in marginal deterioration around the inlay or its failure.
The direction of forces on the occlusal surface of Inlay Fixed Partial Denture may lead to the phenomenon of submargination, ceramic fracture, wear at interface and postoperative hypersensitivity which remain a problem that require further investigation. One of the most important factors in the success and longevity of a restoration is to have an accurate marginal fit. Ideally, the cemented restoration should precisely meet the finish line of the prepared tooth. In reality, clinical perfection is challenging to achieve and to verify.
详细描述
The tub-shaped inlay preparation design this consists of an occlusal proximal reduction featuring a 3.5-4 mm width bucco-lingually, 3-3.5mm depth occluso-gingivally and 7-7.5 mm length mesio distally for molars and 2.3-2.8mm width buccolingually, 3-3.5 mm depth occluso gingivally and 3.5-4mm length mesiodistally for premolars. when necessary, superficial extensions may also be made on the preparations so that the occlusal fossa included in the preparation area and then the susceptibility for plaque accumulation will be diminished.
Participant timeline
The visits will be designated as follows:
Visit 1: one week after allocation, preoperative records, face-to-face adherence reminder session, clinical examination, radiographic examination, intraoral photography and primary impressions for diagnostic cast construction .
Visit 2: one week after the first visit, teeth preparations, secondary impression and temporization .
研究设计
- 研究类型
- Interventional
- 分配方式
- Randomized
- 干预模型
- Parallel
- 主要目的
- Treatment
- 盲法
- Single (Participant)
入排标准
- 年龄范围
- 18 Years 至 55 Years（Adult）
- 性别
- All
- 接受健康志愿者
- 是
入选标准
- •From 18-55 years old, should be able to read and sign the consent document.
- •Ability to tolerate the restorative procedures (physical and psychological).
- •Good oral hygiene
- •Low susceptibility to decay
- •Have a minimum coronal tooth height of 5 mm,
- •Parallel abutments
- •Sufficient mesio distal edentulous gap dimensions.
排除标准
- •Partially erupted teeth (young)
- •Bad oral hygiene and motivation
- •Root canal treated teeth
- •Psychiatric problems or unrealistic expectations
- •Severe para-functional habits
- •The absence of enamel on the preparation margins
- •Extensive crown defects
- •Abutment mobility
研究组 & 干预措施
Tub shaped design
The tub-shaped preparation design this consists of an occlusal proximal reduction featuring a 3.5-4 mm width bucco-lingually, 3-3.5mm depth occluso-gingivally and 7-7.5 mm length mesio distally for molars and 2.3-2.8mm width buccolingually, 3-3.5 mm depth occluso gingivally and 3.5-4mm length mesiodistally for premolars. when necessary, superficial extensions may also be made on the preparations so that the occlusal fossa included in the preparation area and then the susceptibility for plaque accumulation will be diminished.
干预措施: Tub shaped design (Other)
Inlay shaped design
The occlusal inlay had a preparation depth that allowed a thickness of 2.0 mm for the ceramic. The occlusal preparation was 4 mm wide and extended 4 or 6 mm mesio-distally for the premolar or molar models, respectively. The proximal box was 1 mm wide and had approximately 5˚ divergence, extending 2 mm apical to the isthmus floor . The preparations corresponded to a proximal connector area of 3 mm × 3 mm for molars and premolars.
干预措施: Inlay shaped design (Other)
结局指标
主要结局
Fracture
时间窗: one year
Fracture assessed by modified Ryge Criteria ( Alpha , Bravo , Charlie and Delta )
次要结局
未报告次要终点
研究者
mahmoud osama
clinical professor
Cairo University