Clinical Evaluation of High Strength Zirconia-Reinforced Lithium Silicate Chairside CAD/CAM Crowns
Overview
- Phase
- Not Applicable
- Intervention
- Not specified
- Conditions
- Fractured Tooth
- Sponsor
- University of Michigan
- Enrollment
- 48
- Locations
- 1
- Primary Endpoint
- Crown failure
- Status
- Active, not recruiting
- Last Updated
- 7 months ago
Overview
Brief Summary
This investigation will be a clinical trial to study the performance of a newly developed high strength ceramic material for crowns. The ceramic has been approved by the FDA for patient treatment. A computer technique will be used to fabricate the crowns in a single appointment without the need for a temporary crown or second appointment. Two adhesive resin cement techniques will be used to hold the crown to the tooth and they will be evaluated for creating sensitivity to the tooth. The purpose of the study is to measure how well the high strength crowns function over an extended period of time.
Detailed Description
A recently introduced high strength, zirconia-reinforced lithium silicate (ZLS) ceramic material for full contour CAD/CAM crowns is reported to offer a more translucent and esthetic high strength crown in a more efficient oven firing process. Celtra Quatro (Dentsply Sirona) is submitted to a high temperature matrix firing cycle in the SpeedFire oven (Dentsply Sirona) to achieve high strength in less than 5 minutes following milling. It has a reported flexural strength of 650 MPa compared to 450 MPa for lithium disilicate glass ceramic and \> 900 MPa for 3mol% full contour zirconia. Most glass ceramic materials have a recommended material thickness of 1.5 mm to maximize the strength potential of the material. Occlusal reduction resulting in a crown thickness of 1.0 mm, equitable to the recommendation for full contour zirconia crowns, may be considered sufficient to maintain the desired high strength attained by the ZLS material. This would also result in a more conservative tooth preparation. Another potential advantage of high strength ZLS crowns to many clinicians is that they may be inherently strong enough to allow for conventional cementation. However, for less retentive preparations, it may also be possible to adhesively bond the crowns through the use of adhesive resin cements. It is the intent of this investigation to evaluate the clinical application and performance of the new high strength, zirconia-reinforced lithium silicate material (Celtra Quatro) for CAD/CAM-generated chair-side crown applications. Patients will be recruited to have 60 Celtra Quatro crowns prepared and delivered during a single dental appointment using a chairside CAD/CAM system (CEREC/Dentsply Sirona). The crowns will be recalled at 6 months and then yearly for 5 years to evaluate long-term outcomes of the crowns.
Investigators
Dennis J. Fasbinder, DDS
Clinical Professor
University of Michigan
Eligibility Criteria
Inclusion Criteria
- •must have at least one carious lesion or defective restoration or fractured tooth in a molar or premolar
- •reason for restoration should extend more than one-half the intercuspal width of the tooth requiring a full crown restoration
- •Teeth to be vital and asymptomatic prior to treatment
- •No more than two restorations will be placed per patient. If a patient presents with more than two acceptable teeth for the study, molar teeth will be included prior to premolar teeth.
Exclusion Criteria
- •Devital or sensitive teeth
- •Teeth with prior endodontic treatment of any kind
- •Teeth with a history of direct or indirect pulp capping procedures
- •Patients with significant untreated dental disease to include periodontitis and rampant caries
- •Pregnant or lactating women
- •Patients with a history of allergies to any of the materials to be used in the study
- •Patients unable to return for the recall appointments
Outcomes
Primary Outcomes
Crown failure
Time Frame: from delivery of the crown up to 5 years
Restoration failure is scored by visual loss of the crown from the tooth requiring replacement of the study crown with a new crown at any time between delivery and five years.
Secondary Outcomes
- Crown loss of retention(from delivery of crown up to 5 years)
- Margin staining(from delivery of crown up to 5 years)
- Tooth sensitivity(from delivery of crown up to 5 years)